Voir les contributions

Cette section vous permet de consulter les contributions (messages, sujets et fichiers joints) d'un utilisateur. Vous ne pourrez voir que les contributions des zones auxquelles vous avez accŤs.


Messages - nalsur8

Pages: [1] 2
1
Géneral / Global / Re : my hotend not hot
« le: 12 octobre, 2017, 04:08:41 pm »
yes connection not fix between ramps and arduino
now ok.

thanks all

2
Géneral / Global / my hotend not hot
« le: 12 octobre, 2017, 03:21:02 am »
hi to all

suddenly my printer hotend not function mean not hot cool only
i replaced with new brand hotend still same, the thermistor ok no problem
the tip i hold by fingers then the temp reading up.

 thanks

3
this is my fan 80mm  :D

4
Géneral / Global / Re : Build Smartrapcore-alu
« le: 05 mars, 2016, 02:59:51 am »
yes, jumper not proper put it, now stepper motor running what supposed.

thanks to all to help

5
Géneral / Global / Re : Build Smartrapcore-alu
« le: 04 mars, 2016, 04:16:15 pm »
i pull out the belting both motor then manually move +X (pronterface) the motor X and Y turning counter-clockwise, but motor Y faster then X motor, then move +Y the motor Y turning clockwise faster then X motor, but motor X turning counter-clockwise. What i saw motor Y turning faster than X motor although i'm move Y first . It's normal wiring for coreXY?


6
Géneral / Global / Re : Re : Build Smartrapcore-alu
« le: 04 mars, 2016, 01:16:01 pm »
Are the motor well connected? (If one motor is going in the wrong direction, it may look likes this, isn't it? I'm not sure, but check it). In manual, +X goes on the right,  and +Y goes at the bottom of the printer.

you mean +Y move to bottom of printer (front of printer)?, according to assy instruction +Y goes to Back of printer
my printer +Y move to back.

send Gcode manually G1 X50 for test, not only X move Y also move together, move more than 50mm X70 Y20 i measure it with rule

7
new design for my smartrapcore-alu 20x20 Z-axis, design base from Andreas.l wood type http://talk.smartfri.odns.fr/index.php?topic=539.0 a bit changes the design mounting, but not yet complete  :)


8
Géneral / Global / Re : Build Smartrapcore-alu
« le: 04 mars, 2016, 10:07:31 am »
the Merlin configuration.h was download from github https://github.com/smartfriendz/smartrapcore-alu
and just upload to the board, only i change is mechanical endstop XY false Z true that's it because of the wiring.

the motor wiring i think OK because i check manually with Pronterface +X move to right +Y move to bottom(front of printer)
according to assy instruction. BUT when move X axis Y axis also move together, it's normal for core XY principal?

thanks


 

9
Géneral / Global / Re : Build Smartrapcore-alu
« le: 03 mars, 2016, 11:28:38 pm »
The settting is

Amx x: 6000
Amx y: 6000
Amx z: 2000
Emx : 10000
Xstep/m : +080.0
Ystep/m : +080.0
Zstep/m : +0080.0
Estep/m : +0140.0


10
Géneral / Global / Re : Build Smartrapcore-alu
« le: 03 mars, 2016, 03:38:20 pm »
something wrong with my corexy setting, how to fix it

1st time printing size 10x10x2, the result 27x14x2

11
Géneral / Global / Re : Build Smartrapcore-alu
« le: 01 mars, 2016, 04:40:23 pm »
yes good ideal Loggs


12
Géneral / Global / Re : Build Smartrapcore-alu
« le: 01 mars, 2016, 04:05:51 pm »
 :D it's look ok almost center of bed X100 Y100, X0 Y0 going to left bottom side, i change the wiring pin blue+red black+green
was red+blue green+black,

I think my bed out of center, according to assembly intruction distance 151mm from left top to Z linear shaft,
my Z about 155mm



13
Géneral / Global / Re : Build Smartrapcore-alu
« le: 01 mars, 2016, 02:58:26 pm »
According to assembly instruction, smartrapcore wire motor is Red, Grey, Yellow, Green
my motor is Red, Blue, Green, Black (wantai brand), i try to reverse the connection Left to Righ for X connection
and also Y, it run but opposite direction (i.e press -X the motor go to X).


14
Géneral / Global / Re : Build Smartrapcore-alu
« le: 01 mars, 2016, 01:32:30 pm »
Hi Loggs

change the cable  (L - R ) also can not, the endstop be come opposite direction

almost 3 days i was find, searcing, resouces how to solve this problem  :-\
 
how to set it back X0 Y0 to front left corner? i try move it manual to corner then enter code M500 to save it
it same or need to edit in configuration.h






15
Géneral / Global / Re : Build Smartrapcore-alu
« le: 01 mars, 2016, 01:07:43 am »
Thanks Loggs

I'll change and see how it work.


Pages: [1] 2